Machine Foundation Analysis and Design

(4/145)

Description

Machine Foundation Dynamic Analysis (Block Foundation on Soil)

Analyses a rigid rectangular concrete block under a vibrating machine. It calculates the natural and resonant frequencies and the vibration amplitude for the chosen mode of motion, applies the usual static and dynamic rules of thumb, and gives a reinforcement layout and a sketch of the displaced block. An introduction sheet lists general design requirements and the formulae used.

Method

Lumped-parameter elastic half-space: equivalent-radius springs (for example Kx = 32(1 − ν)Gro/(7 − 8ν)), mass ratios, radiation damping (for example Dz = 0.425/√Bz) plus hysteretic damping, and embedment corrections. Magnification factors for constant (reciprocating) or speed-dependent (rotating) forces give the amplitude. Eight motion models: vertical, sliding and rocking about each axis, coupled sliding-rocking about each axis, and torsion.

Inputs

  • Machine type, speed, weight and centre of gravity
  • Footing dimensions and embedment; concrete, steel and cover
  • Soil shear modulus, Poisson’s ratio, unit weight, bearing capacity, damping and allowable amplitude
  • Exciting forces and moments and their positions

Outputs

  • Frequencies, frequency ratio and amplitude for the selected mode
  • Checks of weight ratio (> 5), bearing ratio (> 1.5), amplitude, depth and eccentricity
  • Bar layout, concrete volume and reinforcement weight

The stored example, an 80 kN reciprocating machine at 800 rpm on a 3 × 4 × 1.5 m block embedded 0.5 m (G = 30,000 kN/m², ν = 0.35) with a 15 kN horizontal force, gives in sliding a natural frequency of 11.99 Hz against 13.33 Hz operating, and a peak amplitude of 0.055 mm against 0.15 mm allowed.

Please note

  • The vertical spring’s embedment term is entered as 1 + z·ro/2, not the 1 + 0.4z/ro on the introduction sheet, overstating vertical stiffness. The rocking resonant frequency uses the rotating-mass formula even for reciprocating machines.
  • When damping exceeds 0.707 there is no resonant peak, but a frequency is still shown (vertical mode in the example).
  • One motion model at a time. SI units. No macros; sheets protected.
  • By Turan Babacan. References: Design for Machine Vibration; foundations and structures for vibrating machinery.

Calculation Preview

Turan Babacan (babacan)
24 Apr 2023
File Size 213.02 Kb
Downloads: 706
File Version: 1.0
File Author: Turan Babacan
File Rating (4/145)

 
Full download access to any calculation is available to users with a paid or awarded subscription (XLC Pro).
Subscriptions are free to contributors to the site, alternatively they can be purchased.
Click here for information on subscriptions.
Comments: 8
Hello Turan,
Thank you for your machine foundation calculation. An independent check of the sliding mode in your example gave the same natural frequency (11.99 Hz), damping ratio (0.583) and amplitude (0.0545 mm).
While rewriting the description we found two errors on the draw sheet:
- B112 is =4*G*Rv/(1-v)*(1+z/2*Rv), which evaluates 1 + z·Rv/2 (1.489 in the example). The INTRO sheet states the embedment factor as 1 + 0.4(d/ro) (1.102 here), so the vertical stiffness is overstated by about 35%.
- F123 and L123 have the same formula in both branches of the IF, fn/√(1 − 2D²), the rotating-mass peak, so reciprocating machines get the wrong rocking resonant frequency. D122, B122 and P123 use fn·√(1 − 2D²) for that case.
You may also want to consider the ABS(1 − 2D²) in the resonant frequency cells: when D exceeds 0.707 (the vertical mode in the example, D = 0.728) there is no resonant peak, but a frequency is still shown.
We have mentioned these points in the file's description so users are aware. If you upload a corrected version, we will review it and publish it as the next version.
ExcelCalcs Review Team
jcvaladez 7 years ago
HOLA, BUEN DIA. ME INTERESA ADQUIRIR ESTA HERRAMIENTA EN EXCEL. COMO PUEDO CONSEGUIRLA?
fbennettst666 7 years ago
very good excel sheet
johndoyle-admin 8 years ago
Welcome to ExcelCalcs. May I refer you here to a FAQ [Trouble with Units](/support/faqs/trouble-with-units/)
johndoyle-admin 12 years ago
See [FAQ Units](/support/faqs/trouble-with-units/)
mbhatti 12 years ago
I like Machine Foundation and many others. How can I use them for English Units like Fett and pounds etc and not metric???ThanksMax Bhatti
cedarcorp 12 years ago
Wondering about whether the checks for the foundation/equipment ratio changes for rotary (3 x machine weight) and reciprocating (5 x machine weight) - right now it seems locked to 5 x weight for reciprocating
johndoyle-admin 12 years ago
Not content with covering all aspects of civil and structural engineering I see you are starting to encroach on the ground of the mechanical engineer! Amazing stuff Turan (again!)